Logic device/transceiver/encoder

CD4073B CMOS triple 3-input AND gate

Belonging series of logic circuit: 74LVC Logic type: NAND gate Number of channels: 1 Number of inputs per channel: 2 Power supply voltage: 1.65V~5.5V Quiescent current (maximum value): 4uA Maximum propagation delay at different V, maximum CL: 4ns@5V,50pF Low level output current (IOL): 32mA High level output current (IOH): 32mA Logic level-high: 1.7V~2V Logic level-low: 0.7V~0.8V Operating temperature: - 40℃~+105℃

LSF0204 4-Bit Bidirectional Multi-Voltage Level Translator for Open-Drain and Push-Pull Applications

The FXMAR2102 is a high-performance configurable dual-voltage power converter that provides bidirectional voltage translation over a wide range of input and output voltage levels. At the same time, FXMAR2102 can also work in a push-pull environment. designed to work with I

SN74LVC1G04 Single Inverter

Dual Negative Edge Triggered D-Type Flip-Flops with Clear and Preset 14-SOIC -40 to 85

SN74AUP1T87 Low Power, 1.8/2.5/3.3V Input, 3.3V CMOS Output, 2-Input X-NOR Gate

The MC10LVEP16 is a world-class differential driver/receiver. This device is functionally identical to devices EL16, EP16, and LVEL16. Since the output transition time is significantly faster than the EL16 and LVEL16, the LVEP16 is ideal for interfacing with high frequency and low voltage (2.5 V) supplies. Single-ended input operation is limited to VCC >= 3.0 V in PECL mode, or VEE <= 3.0 V in NECL mode. The VBB pin is used as an internally generated power supply for this device only. For the single-ended input case, connect the unused differential input to VBB as the switch reference voltage. VBB can also re-bias AC-coupled inputs. When used, VBB and VCC are decoupled with 0.01 uF capacitors and limit current source or sink to 0.5 mA. VBB should be left open when not in use. The 100 Series includes temperature compensation.

Dual Positive Edge-Triggered D-Type Flip-Flop with Clear and Preset 14-SOIC -40 to 85

6-Channel 4.5V to 5.5V Inverter with Schmitt Trigger Inputs 14-PDIP -55 to 125

CD4049UB CMOS Hex Inverting Buffer/Converter

SN74LS163A Synchronous 4-Bit Binary Counter

CD4042B CMOS Quad Clock "D" Latch

The VHC123A is an advanced high-speed CMOS Monostable multivibrator fabricated in a silicon-gate CMOS process. It achieves high-speed operation similar to an equivalent bipolar Schottky TTL while maintaining CMOS low power consumption. Each multivibrator has a negative A and a positive B transition trigger input, both of which can be used as inhibit inputs. A clear input is also included, which if asserted low resets the one-shot operation. The VHC123A can be triggered on positive transitions of this clear input while A is held low and B is held high. The output pulse width is determined by this formula: PW = (Rx)(Cx); where PW is seconds, R is ohms, and C is degrees Fahrenheit. Rx and Cx limits are: External Capacitor, CxNo Limit External Resistor, Rx VCC = 2.0V, 5 kohm Min VCC > 3.0V, 1 kohm Min An Input protection circuit ensures that 0 to 7V can be applied to the input pin, Regardless of the supply voltage. This device can be used to interface 5V systems with 3V systems and both power systems, such as battery backup. This circuit prevents damage to the device due to mismatched supply and input voltages.